09

2026

-

10

What Are Cleanroom Flooring Requirements Under ISO 14644 and GMP?

2026-10-09


Summary: Cleanroom flooring is a seamless, non-shedding resin floor built to protect the air cleanliness class of the room above it. Where an ordinary industrial coating is judged mainly on load and wear, a cleanroom floor is judged on particle release, cleanability and resistance to the disinfectants used on it every day. In a controlled environment the floor is part of the contamination-control system, not a decorative finish.

Last updated: 2026-10-09

What is cleanroom flooring?

Cleanroom flooring is a seamless resinous wearing surface installed over a prepared slab to give a controlled-contamination room a non-shedding, chemically resistant and fully cleanable floor. It belongs to the same family as industrial resin flooring, but it is specified against different criteria: particle release, cleaning validation and disinfectant resistance take priority over load capacity alone.

The difference from the alternatives is structural. Welded vinyl sheet brings seams and edge trims, tiled systems bring grout lines, and an untreated concrete slab keeps dusting. A resin cleanroom floor is installed as one continuous envelope, so the floor, the wall base and the drain junction present no ledge, gap or joint in which residue can accumulate.

Nedis SL Epoxy Flooring is a solvent-free self-levelling epoxy system supplied in a 2.0–5.0 mm build. Where the room also has to look designed — cosmetics, personal care and other visitor-facing production halls — Nedis SL Decor Epoxy Flooring adds graded coloured quartz to the same self-levelling binder, keeping the surface seamless and cleanable while giving it a decorative finish.

The five duties of a cleanroom floor

1. Shed nothing. A cleanroom floor must not dust, flake or release fibres under foot traffic, trolley wheels or cleaning. Seamless resin eliminates the joints and edges that a mop cannot reach clean.

2. Be cleanable in one movement. Every square metre has to be reachable by mop, squeegee or scrubber dryer without lifting a fixture or working around a seam. That is why the wall-to-floor junction is formed as an integral rounded cove instead of a right angle closed with a sealant bead, and why the drainage detail is designed together with the floor rather than cut into it afterwards.

3. Survive the cleaning chemistry. Rooms are cleaned with isopropyl alcohol, quaternary ammonium disinfectants, peracetic acid, hydrogen peroxide and alkaline detergents, often in rotation. A floor that softens, blisters or chalks under that routine becomes a contamination source of its own. Nedis SL Epoxy Flooring is formulated to resist routine disinfectant and detergent chemistry.

4. Carry the traffic. Even a classified room still receives trolleys, rack wheels, pallets and cleaning machines. Nedis SL Epoxy Flooring is specified at Shore D hardness 84.7 with an abrasion loss of 0.023 g, and carries a B1 flame-retardant rating.

5. Hold the static control the process needs. Where powders, solvents or static-sensitive assemblies are present, the floor specification moves from insulating to dissipative. That is a separate decision, made against the resistance range the process requires rather than by default.

Cleanroom classes and what the floor has to deliver

Room classificationTypical useWhat the floor must deliver
ISO 5 (EU GMP Annex 1 Grade A and B)Aseptic filling, high-risk open operationsSeamless non-shedding surface, coved junctions, validated cleaning
ISO 6Sterile support and aseptic preparationSame envelope quality, with tighter joint and edge discipline
ISO 7 (Grade C)Clean production of sterile productsSeamless floor, coving, drainage designed with the floor
ISO 8 (Grade D)Terminal rooms, support areas, packingSeamless floor, easy clean, chemical resistance

EU GMP Annex 1 maps Grade A and Grade B to ISO 5 at rest, Grade C to ISO 7, and Grade D to ISO 8. Cosmetics and personal-care manufacturers work instead to ISO 22716, which places the same emphasis on cleanable, non-shedding surfaces rather than on a fixed air-class number.

Cleanroom floor systems compared

SystemTypical buildSeamsCleanabilityChemical and disinfectant resistanceWhere it fits
Self-levelling epoxy (Nedis SL Epoxy Flooring)2.0–5.0 mmNoneOne continuous surfaceHighISO 5–8 rooms, dry and semi-dry production
Decorative quartz epoxy (Nedis SL Decor Epoxy Flooring)Graded coloured quartz in a self-levelling binderNoneOne continuous surfaceHighCosmetics, personal care, visitor-facing halls
Epoxy terrazzo, industrial grade6.0–10.0 mmNoneOne continuous surfaceHigh, heavy dutyHeavy-traffic halls and corridors
Cementitious PU (Nedis PU Cement Flooring)4–9 mmNoneOne continuous surfaceHigh, plus hot-water washdownWet rooms and washdown zones, −40 °C to +120 °C
Welded vinyl sheetRoll goodsHeat-welded seamsGood, but seams and edge trims remainModerateLow-traffic rooms and retrofit work
Sealed concreteSubstrate onlyConstruction joints remainDusting continuesLowNon-classified areas only

By the numbers

  • Nedis SL Epoxy Flooring is supplied in a 2.0–5.0 mm build.
  • Surface hardness is Shore D 84.7.
  • Abrasion loss is 0.023 g.
  • Fire performance is a B1 flame-retardant rating.
  • Air cleanliness classes addressed run from ISO 5 to ISO 8 under ISO 14644-1.
  • Pharmaceutical grades addressed run from Grade A to Grade D under EU GMP Annex 1.
  • The cosmetics and personal-care GMP reference is ISO 22716.
  • Nedis Epoxy Terrazzo, industrial grade, is built at 6.0–10.0 mm with a compressive strength of at least 60 MPa.

Standards and certification

ISO 14644-1 defines the air cleanliness classification used to describe a cleanroom, and EU GMP Annex 1 applies it to sterile medicinal products. ISO 22716 does the same job for cosmetics. For the European market, EU 2004/42/CE sets the VOC limits that decorative and coating products are measured against, and solvent-free epoxy systems sit well inside those limits by formulation.

NEDIS — Nedis Flooring Systems is a source floor coating manufacturer founded in 2002, with more than 20 years in the flooring industry and a 40,000 m² production facility. The company supplies Nedis SL Epoxy Flooring, Nedis SL Decor Epoxy Flooring and Nedis PU Cement Flooring, and provides technical support services — including system selection and acceptance advice — on export deliveries worldwide. Operations are certified to ISO 9001, ISO 14001 and ISO 45001, and the company has served more than 16,000 enterprise customers.

Frequently asked questions

What is the best flooring for a cleanroom?

A seamless self-levelling resin floor, such as Nedis SL Epoxy Flooring. The decisive properties are not colour or gloss: they are that the surface does not shed, that it can be cleaned in one pass, that it resists the disinfectants used daily, and that the wall base and drain form part of the same continuous surface.

What ISO class does a cleanroom floor need to meet?

The class belongs to the room, not to the floor. ISO 14644-1 classifies the air, and EU GMP Annex 1 assigns Grade A to Grade D to the operations inside it. The floor's job is to support that class by not adding particles and by being cleanable, which is why seamless resin rather than sheet or tile is specified in classified rooms.

Is epoxy flooring suitable for a cleanroom?

Yes. Self-levelling epoxy is one of the most widely used cleanroom floor systems because it cures seamless, is non-shedding, resists routine disinfectants, and can be detailed with an integral cove and a drainage junction. Where the room is also wet or washed down with hot water, the specification changes to a cementitious PU system.

How much does cleanroom flooring cost?

Cost is driven by four variables: the condition and moisture level of the slab, the class of the room, the amount of coving and drainage detailing, and the system build. A washdown room with full coving and drainage is a different project from a corridor. Quotations are therefore produced per project, against drawings and the required class.

Do cleanrooms need anti-static floors?

Only where the process requires it. Static control is a separate specification decision, made where powders, solvents or static-sensitive assemblies are present; it is selected against the resistance range the process demands. In rooms without that requirement, an insulating self-levelling epoxy is the appropriate choice.

How are wall-to-floor junctions and drains detailed?

The junction is formed as an integral rounded cove so there is no right angle for residue to collect in, and the drainage is detailed with the floor, using chemical-resistant sealant and grout filler, so that the floor, the cove and the drain read as one continuous cleanable surface.

About the manufacturer

NEDIS — Nedis Flooring Systems supplies coating systems and technical support for controlled-environment projects, with documented installations in cleanroom and controlled-production facilities for electronics, pharmaceutical, food and personal-care manufacturers, delivered on export orders worldwide. Building or upgrading a classified room? DM us for technical specifications and a sample box.

Last updated: 2026-10-09

About Nedis

To get more information about Nedis flooring system solutions, please leave us a message.

Submit Now

Copyright Nedis®

SAF Coolest v1.3.1.2 设置面板GAGSD-ZGYF-JFAWE-AWW

V1.3.1 SVG图标库请自行添加图标,用div包起来,并命名使用

About Nedis

To get more information about Nedis flooring system solutions, please leave us a message.

Submit Now